Kalkulator Saiz Tayar – Dimensi, Perbandingan & Setara

Understanding Tire Size Numbers

Tire sizes look complex but follow a simple formula. A tire marked 225/55R17 means: 225 mm wide, 55% aspect ratio (sidewall height = 55% of width), and fits a 17-inch rim.

The key measurements derived from these numbers:

• Sidewall height: Width × Aspect Ratio / 100 = 225 × 0.55 = 123.75 mm
• Total diameter: (Sidewall × 2) + (Rim × 25.4) = (123.75 × 2) + (17 × 25.4) = 247.5 + 431.8 = 679.3 mm
• Circumference: π × Diameter = 3.1416 × 679.3 = 2,134 mm
• Revolutions per km: 1,000,000 mm ÷ Circumference = 469 rev/km

This naming convention follows the ISO 4000-1 and ETRTO (European Tyre and Rim Technical Organisation) standards. The format is: Width / Aspect Ratio + Construction Type + Rim Diameter. The "R" stands for radial construction — the dominant tire type since the 1970s. You may occasionally see "D" (diagonal/bias-ply) on trailers or vintage vehicles, or "B" (bias-belted) on older specifications.

Beyond these three numbers, a full tire designation includes additional codes. For example, 225/55R17 97W adds a load index (97 = 730 kg per tire) and a speed rating (W = 270 km/h maximum). Understanding these codes is critical when selecting replacement tires — the law in most jurisdictions requires matching or exceeding the vehicle manufacturer's specified load and speed ratings.

Complete Tire Size Formulas

Every measurement you need can be derived from the three primary numbers (width, aspect ratio, rim diameter):

Note: These are theoretical dimensions. Actual tire dimensions vary slightly by manufacturer, inflation pressure, and load. A tire inflated to 35 psi will have a slightly larger diameter than the same tire at 28 psi. Always measure loaded radius for precise speedometer calibration.

How Tire Size Affects Your Vehicle

Changing tire size affects multiple aspects of vehicle performance and safety:

The most important rule when changing tire sizes: keep the overall diameter within ±3% of the original to avoid speedometer errors, ABS interference, and clearance problems.

Speedometer Error from Tire Size Changes

Your vehicle's speedometer is calibrated for a specific tire circumference. When you change tire sizes, the speedometer reading drifts proportionally to the diameter change:

Speedometer error (%) = ((New diameter − Original diameter) ÷ Original diameter) × 100

A larger tire makes the speedometer read slower than actual speed (you're going faster than indicated). A smaller tire makes it read faster (you're going slower than indicated).

In the EU, regulation ECE R39 requires speedometers to never indicate a speed lower than actual. Manufacturers typically calibrate speedometers to read 3–5% high at factory tire sizes, providing a safety margin for slight tire size changes. In the US, FMVSS 127 governs speedometer accuracy, allowing up to ±5 mph at 80 mph.

Plus Sizing: Upgrading Your Wheels

Plus sizing means increasing rim diameter while reducing aspect ratio to maintain overall tire diameter. This improves handling and aesthetics:

Lower profile tires (smaller aspect ratio) provide better lateral stability and more precise steering response, but transmit more road vibration and are more susceptible to pothole damage.

When plus-sizing, verify that the new wheel/tire combination fits within the wheel well at full steering lock and full suspension compression. Consult the vehicle manufacturer's approved tire size list or a reputable tire fitment database. Most manufacturers publish approved alternate sizes in the owner's manual.

Load Index and Speed Rating Reference

Every passenger tire carries a load index number and speed rating letter after the size designation. These are not optional — they are legally required specifications.

Always match or exceed the original load index and speed rating. Downgrading either can compromise safety, void insurance, and fail vehicle inspections.

Popular OEM Tire Sizes by Vehicle Type

These are the most common factory-fitted tire sizes across different vehicle categories (as of 2024–2025 model years):

EV-specific tires (often marked "EV" or "elect") feature lower rolling resistance compounds, reinforced sidewalls for the heavier battery weight, and foam inserts for noise reduction. Standard tires on an EV wear out 20–30% faster due to the higher torque delivery.

Metric vs. Flotation Tire Sizing

Light truck and off-road tires sometimes use flotation sizing instead of metric. A tire marked 33×12.50R15 means: 33 inches overall diameter, 12.50 inches wide, fits a 15-inch rim.

To convert between the two systems:

Off-road fitment often requires lift kits, fender trimming, and re-gearing the differential to compensate for the larger diameter. Consult your vehicle's axle ratio tables and state regulations before upsizing significantly.

Tire Pressure and Its Effect on Dimensions

Inflation pressure directly affects tire dimensions, load capacity, and performance. The recommended pressure is printed on the vehicle's door placard (not on the tire sidewall — that number is the maximum pressure).

Check tire pressure monthly and before long trips. Pressure increases approximately 1 psi per 5.5°C (10°F) rise in ambient temperature. A tire that reads 32 psi on a 20°C morning may read 35 psi after highway driving heats it up — this is normal and expected. Always measure pressure cold (before driving or within the first 1–2 km).

Tire Types: All-Season vs. Summer vs. Winter

Tire compound and tread pattern dramatically affect performance in different conditions. Choosing the right type for your climate is as important as choosing the right size:

The 3PMSF (Three-Peak Mountain Snowflake) symbol on the sidewall indicates the tire meets the ASTM F1805 traction test for snow performance. The older "M+S" marking is self-certified by manufacturers and does not require testing — it offers no guarantee of actual snow performance. In countries with winter tire mandates (Germany, Austria, Czech Republic, parts of Canada), only tires with the 3PMSF symbol satisfy the legal requirement.

Summer tires harden and lose grip below 7°C, even on dry roads. Braking distance on cold, dry pavement at 5°C can increase by 10–15% with summer tires versus winter tires. Conversely, winter tires wear rapidly in hot weather — their soft compound can lose 30–40% more tread per km at 30°C compared to summer tires.

Reading Tire Wear Patterns

Uneven tire wear reveals alignment, pressure, or suspension problems. Here's how to diagnose common patterns:

The minimum legal tread depth in most US states is 2/32" (1.6 mm), indicated by built-in tread wear indicators (TWI bars). However, safety experts recommend replacing tires at 4/32" (3.2 mm) — wet braking distance increases significantly below this threshold. In rain at highway speed, tires at 2/32" need up to 80% more distance to stop than tires at 4/32".

Regular tire rotation (every 5,000–8,000 miles / 8,000–12,000 km) equalizes wear across all four tires, extending their useful life by 20–30%. The recommended rotation pattern depends on whether you have directional tires, staggered fitment, or a full-size spare.

TPMS: Tire Pressure Monitoring Systems

Since 2007 in the US (FMVSS 138) and 2014 in the EU (ECE R64), all new passenger vehicles must include a Tire Pressure Monitoring System. There are two types:

The TPMS warning light triggers at 25% below recommended pressure. For a 32 psi specification, the light activates at 24 psi. By this point, fuel economy is already reduced by 2–3%, and tire wear is accelerated. Don't rely solely on TPMS — check pressure manually once a month.

When changing tire sizes, direct TPMS sensors must be transferred to the new wheels (or new sensors purchased and programmed). Some aftermarket wheels require special TPMS-compatible valve stems due to clearance differences.